Exterior vent screws

General Technical Questions and Answers last answered over 1 year ago.
You may also want to visit the Wiki(pedia) for a more structured index of T25 repair, maintenance, technical and ownership topics

Moderator: Moderators

Forum rules
You cannot post in this Archive forum (read only).
If you require to re-raise one of these topics in the live 80-90 forums, please insert a link to it in your first post.

Exterior vent screws

Postby Fingle » 03 Mar 2009, 11:56

I have just recieved my new fridge vents for the exterior of the van, the old screws are corroded to buggery.
1: How can i get em out without angle grinding them
2: Can I buy new ones (self tappers?) from BandQ?
Fingle
 
Joined: 19th, Oct 2018

Re: Exterior vent screws

Postby jamesc76 » 03 Mar 2009, 12:00

Is the new vent the same as the old one ie are screws in the same place??? If not good luck i would try the srews then if not havint it rip the old vent off and try mole grip's/vice grips on them??
DJ at Dubdayz Summerfest
Now cutting about in an LT35 MWB
User avatar
jamesc76
 
Posts: 6240
Joined: 14th, Oct 2005
Location: Nottingham
80-90 Mem No: 1186

Re: Exterior vent screws

Postby Fingle » 03 Mar 2009, 12:56

Yeah same vent.

Luckily the screws afre coming out today...last time i tried was summer so maybe they had expanded
Fingle
 
Joined: 19th, Oct 2018

Re: Exterior vent screws

Postby rainman » 03 Mar 2009, 12:56

I had to hammer mine out from the inside. They were so rotten they didn't put up much resistance.
1983 2L a/c CU homebrew (ex-Autohomes Kamper)
User avatar
rainman
 
Posts: 367
Joined: 10th, Sep 2007
Location: Gloucestershire
80-90 Mem No: 4142

Re: Exterior vent screws

Postby cubensis » 03 Mar 2009, 17:34

Last time i attached mine (last summer)i cut up a rubber inner tube and made a seal (basically four rectangle strips) to go between the van body and the vent, seems to have worked well.
1986 WBX 1.9 DG engine (originally a DF engine)
User avatar
cubensis
 
Posts: 124
Joined: 2nd, Jun 2008
Location: Manchester
80-90 Mem No: 0

Re: Exterior vent screws

Postby scamperman » 03 Mar 2009, 17:39

Hi,
if the screws aren't case hardened you can drill the heads off,remove the old, vent then i would undo the screw stubs by grabbing with side cutters/mould grips or such like.
James
scamperman
 
Posts: 40
Joined: 8th, Jun 2007
Location: Stafford
80-90 Mem No: 3422

Re: Exterior vent screws

Postby getunder » 03 Mar 2009, 20:41

Lots of plus- gas or WD 40.Try tightening them a tiny bit first, might be some better screwdriver bite.Also impact screwdriver. . For some applications I have used a mini pencil blowlamp, still made but need searching for.recharged from Cig lighter can. Flame spread can be limited with a metal sheet with a small hole. Many, many times.
getunder
 
Posts: 1807
Joined: 20th, Feb 2009


Return to Technical Questions and Answers (archived from live forum)

Who is online

Users browsing this forum: No registered users and 8 guests

cron